Jump to content

carlm

Registered Users - Approved
  • Posts

    15
  • Joined

Converted

  • Location
    Grandville, Michigan

Converted

  • FusionPro Products
    Yes

Converted

  • FusionPro VDP software version
    8.0.20

Converted

  • OS
    Windows2008Server R2

Converted

  • Acrobat Version
    Acrobat X (10)

carlm's Achievements

Apprentice

Apprentice (3/14)

  • Week One Done
  • One Month Later
  • One Year In
  • First Post Rare
  • Collaborator Rare

Recent Badges

10

Reputation

  1. The output to new pdf worked perfectly. It wasn't exactly what we were looking for but as a work-around its doing the job just fine. Thanks Dan!
  2. Purpose is two-fold. First: The product shipped must be perfed sheets of imposed pages Left to Right, Top to Bottom (and break into next press sheet as needed). Second: When the shipping destination changes, we want to stop imposing on the current sheet and immediately start a new press sheet so that the new store info starts on a new sheet. I tried setting the last dropdown to stack w/count of 1 w/o any luck. ..Simplex Horz 14, Vertical 10, Stack 1 OnRecordStart...StartNewStack()...no change. OnRecordStart...StartNewSheet()...complains about a non-assigned body page.
  3. Not a silly question..silly end user maybe but don't assume anyting . So per your response Dan, is there a way StartNewSheet() type function when imosing sheetwise instead of the StartNewStack()?
  4. Added/Updated my signature so you can see what I'm running...sorry. I found the definition of the function in the RulesSystemGuide.pdf. It states that "If imposing by stacks, this will trigger a new stack..." Since we are imposing by sheet and did NOT select STACK from the dropdown in the FPIImposer tool, this might turn the function OFF. If this is the problem, how can we start a new imposition page if we do not use the STACK dropdown?
  5. Update: In OnRecordStart, when I replace the FusionPro.Composition.StartNewStack() with ReportWarning("Detected Change"); I'm getting the change detected properly and it shows up in the MSG log just fine. I'm missing something about what it takes to truly trigger the new stack.
  6. We have a template with 4 pages: MasterFront, MasterBack, SpacerFront, SpacerBack. In OnRecordStart, we turn these On/Off as needed based on column/field values coming thru the record. Before running any of the above rules we have as the very first rule in OnRecordStart..the following if (FieldChanged("NewStackTrigger")) FusionPro.Composition.StartNewStack(); Everything works normally but we do not generate the start of a new stack when the field changes. The PDF is imposed sheet-wise...left to right, top to bottom and then down to the next sheet (this is what we want so far) Example: We run some data that fits on a single sheet (front and back) but the data DOES have values that should kick off a new sheet..we should generate 2 sheets front and back even if the sheets are not "filled" up w/imposed records Any ideas? IsStartNewStack() 2side aware? Are there composing errors that could prevent this? Thank you!
  7. Ok...then we'll continue to use Windows 2003 for now. THanks! cdm
  8. THis is a Windows 2008 server installation. What you are describing sounds like a regular font installation. Apparently that is not enough for setting up FusionPro Server on Windows 2008. We were told that it required some special steps just like an installation on Vista.
  9. Sorry...I meant to say that our 2003 servers are working just fine
  10. There are some special settings to turn on in 2008 EE to get the fonts to load properly. Apparently it is the same issue as under Vista. Can someone tell me the steps to load fonts properly? We are having rendering issues and think that this may be the problem...our 2008 servers are working just fine. Thank you for your help!
×
×
  • Create New...